top of page

Energy Saving

H.R.T.I. - 1200 Solvent Base 

Thermal Insulation Coating

e8p

  • Product

Energy Saving - 

H.R.T.I. - 1200 Solvent Base Thermal Insulation Coating

  • Trade Information

  • Unit of Measure : - Litre / Litres

  • Min. Order Quantity : - 10 Litres

  • Main Domestic Market : - INDIA  

  • Description

e8d

  • Excellent Product for Energy Saving Coating Upto 1200 Deg C.

  • This product is used for achieving heat resistant with thermal insulation of the surface where the temperature is more than 600 degrees C and less than 1100 degrees C .

  • It is tested by I. I. T. Mumbai. And National Coatings Corporation California, U. S. A.

  • If undisturbed it does not need reapplication for about three years.

  • Application

  • H R T I 1200 Coating is specially manufactured for coating of parts of furnaces which come into contact of heat upto 1200 deg. Celsius

  • This is suitable product for application on metal surfaces. For application over bricks, our water base product should be used.

  • In industries where heat is used for process,  THERMAL INSULATION COATINGS are used for energy saving purpose up to 1800 degrees C.

  • It reduces heat transfer from inner shell to exterior and hence reduces fuel consumption thereby increasing energy saving.

  • Features

  • H R T I 1200 Coating is specially manufactured for coating of parts of furnaces which come into contact of heat upto 1200 deg. Celsius.

  • This coating increases the life of parts of furnace or the parts on which they are applied for protection by providing thermal insulation to them by radiation control.

  • The heating in sunlight is mainly due to radiation. Conduction and convection are secondary which transfer such generated heat.

  • Conventional insulating products are designed to prevent conduction and convection.

  • THERMAL INSULATION COATING is the only product which takes the care of radiation.

  • Being elastomeric it takes the care of expansion and contraction of the surface on which it is applied. Also after application of this, any conventional waterproofing is not required to the building.

  • Since it is always visible on the top, any damage to it due to drilling, hammering or chipping can be repaired there only.

  • On a bare furnace exterior surface, it’s application has shown the minimum reduction of 10% in temperature. (Deg Celsius) checked with infrared thermometer.

  • In some cases where the application is done both interior and exterior, 40% saving is achieved. Hence ideal saving can be achieved just by applying  THERMAL INSULATION COATING paint.

  • This coating increases the life of parts on which they are applied for protection.

e8f

  • Application Procedure

  • The application procedure of  HEAT RESIST 1200 is very easy.

  • It can be applied by brush after mixing it well and thinned down to application viscosity if required.

  • It does not need any primer.

  • The previously applied coating should be removed from the surface by  PAINT STRIPPER. The paint stripper should be applied to the surface and left for few minutes till the paint starts lifting from the surface.

  • Then the surface should be scraped lightly with the help of emery paper. The surface should then be cleaned by thinner followed by application of one coat of  H R T I 1200.

  • The surface should be air-dried for one hour and then should be heated and maintained to 250 deg Celsius for one hour.

  • If it is not possible to heat and maintain the surface to that temperature for the specified period, the painted surface should be taken in use, without touching it and it will automatically dry in warm conditions within 3 to 4 days, depending upon the amount of heat it receives.

  • Then the second coat in such condition should be applied after complete drying of the first coat.

  • Similarly third coat should be applied for getting good results of thermal insulation.

e8ap

  • Disclaimer

The technical specification is correct to the best of our knowledge and under test conditions and we do not accept any liability towards misuse and contents of it. Product must be tested for specific use prior to use. For further details or any queries please do not hesitate to contact us.

bottom of page